Xytronic LF-853DTP 5 in One Multi-Function S.M.D. Rework Station. This Xytronic LF-853DTP Rework Station is the best tool for repairing work, combination with Xytronic LF-852D and LF-8800 which is specially designed for lead free soldering / desoldering, surface mount devices with temperature controlled hot air.
Xytronic LF853DTP Rework Station Product Features
1. Xytronic LF853DTP 5 IN ONE Rework Station: By design, saving working space, owning three function, can greatly meet the users need. Soldering, Desoldering, and Hot Air Rework Station.
2. LF853DTP SPECIAL INTELLIGENT CHIP MICROCOMPUTER CONTROL: Designed, double LED display operating by pressing keys, make it convenient and comfortable operation.
3. LF853DTP TEMPERATURE SELECTION: Fahrenheit and Centigrade (Celsius) temperature.
4. LF853DTP HEATER/SENSOR FAILED DETECTION: If sensor circuit fails, the display reads "S--E" and cut off the heater power. If heater circuit fails, the display will read "H--E" and cut off the heater power. 5. TEMPERATURE "LOCK-OUT" FEATURE: The temperature can be locked by "password" code that is convenient for production line management.
6. LF853DTP ESD SAFE AND SPIKE FREE CIRCUITRY: The "Zero Voltage" electronic switching design also protects voltage and current sensitive components (CMOS devices, etc.) against damaging current and transient voltage spikes commonly produced by less efficient, mechanically switched stations.
7. LF853DTP DELAYED SUCTION: To eliminate the problem of solder clogging up the tip, a delayed switch feature has been incorporated for the unit that allows the pump to continue sucking for 1.5 seconds after the actuator switch is released.
8. LF853DTP LIGHTWEIGHT SOLDERING IRON: Ergonomic mini handle that stays cool and prevents operator fatigue.
9.
LF853DTP ENERGY SAVER MODE: If the station has been idle for 20 minutes, the energy saver feature will automatically engage, the temperature goes down to 150°C from the set temperature. Activating the solder/desolder wands will disengage the power saving feature and the unit will immediately ramp up to the preset temperature. When over 40 minutes without operation the main power will be switched off to "sleep mode" which cuts power consumption and extends tip life.
Please note:
You have to switch off the Xytronic LF-853DTP Rework Station first and then switch "ON" again to commence work when the unit goes to "Sleep" mode.
10. LF853DTP IRON WORKING OPTION: Both soldering, desoldering irons of the Xytronic LF853DTP Rework Station can be used at the same time. You can also set by pressing keys " SET + ▲" when you only use soldering or desoldering iron. At this time, the LF853DTP iron which you set will enter the power off suspend status. It means that the heater power is cut off. If press "▼"then the heater power will be on.
11. LF853DTP SMD TWEEZERS : The additional feature is specially designed for SMD chips, SOT, Flat pack ICs' etc. reworking. TWZ90 Tweezers can be interchangeable with soldering iron as an option. Be sure before proceeding this operation, the main switch must be "OFF" to avoid any damage to the unit.
Xytronic LF-853DTP Rework Station Accessories
Xytronic 307K
Xytronic DIA100 Desoldering Iron
Xytronic HAP 80 Hot Air Wand
Xytronic TWZ100 Hot Tweezers
Replacement Heating Element for Hot Air Wand 79-460012
Purchase the Xytronic LF853DTP Rework Station Today!
Howard Electronics offer you the customer the best Vendor selection of Soldering and Desoldering tools, SMD Rework, Heat Guns, Microscopes, and Specialty tools you could ask for. Our vendors are Atten, Auburn Technology, Chip Quik, Den-On Instruments, EDSYN, Goot, Hei Scope, JBC Tools, Jensen Global, Jovy, Mag Eyes, Master Appliance, Midwest Devices, MG Chemicals, Pana Vise, Qualitek, Steinel, Scienscope, Virtual Industries, Weller, and Xytronics. Please select the best vendor for the tools that you require.