Secure Site
|
|
Call 1-800-394-1984 Toll Free (USA and Canada) HEI now offers you a 60 day 100% Total Satisfaction Guarantee. Call us and still receive the 5% Discount for shopping on the internet. New Low Price Guarantee from HEI. Monthly Specials |
|
|
Secure Site | ||
| No Sales Tax outside of Kansas |
7th Newsletter from Howard
Electronic Instruments, Inc.
October, 2001
You are
viewing in HTML:
In this Newsletter:
* PDR 710 Solderlight (SMT Rework
System)
* 15% off of all Scienscope Microcscopes
& Video Inspection Stations (October Only)
* Tips for Xytronic Soldering and Desoldering Stations
* 60 day
100% Total Satisfaction Guarantee
|
PDR 710 SOLDERLIGHT |
ELECTRONIC CONTROLLED HAND-HELD SMT
REWORK SYSTEM
The PDR 710 SolderLight
is a low cost SMT rework system, using PDR’s patented IR Handtool technology
that has been specifically designed to cope with the challenges of repairing
today's PCB assemblies. No more blowing discrete components off of the board. No
air flow - Just good solid IR heat from top to bottom.
|
|
HEI Price $2395.00 | |||
Call 1-800-394-1984 To Order www.howardelectronics.com/pdr/710.html |
The power controlled IR handtool is simple to use and enables
a good process necessary for the effective soldering/de-soldering of most
advanced SMT packages, including BGAs, QFPs, PLCCs, SOICs, standard SMDs,
also SMT Sockets and Connectors
The SolderLight comes with a good range of standard features allowing the operator to quickly and safely rework all types of components without the need for specific tips or nozzles, and without overheating the component, adjacents or the PCB. It uses all the proven attributes of PDR’s IR technology introduced in 1987 and used worldwide by over 3000 customers.
|
FEATURES |
|
|
Digital Electronics
Control
-PDR digital control
-Simple dial setting power
controls
Optional Paste stencil
System
-Hand held stencil tool by
PDR
-Fits Stencils by Mini Micro
Stencil
Advanced Hand Held Infra-Red (HIR)
Heating
-Electronically controlled 150W HIR
soldering/desoldering tool
-Manual scanning action heats all
surface mounted devices. |
500W IR Back Heater System
-medium wave IR PCB
preheating
-500W, 120mm x120mm area heating
zone
Professional PCB Workholder
System
-Precision bench mounted
workholdersystem
-Up to 16" X 12" (420mm X 300mm)
capacity
| ||
| |||
To Order Call
1-800-394-1984 and tell us
you seen it in the newsletter to receive the Newsletter Special Price.
 SSZ Series Stereo Zoom Microscopes
from Scienscope |
| 15% off of these prominent Scienscope Microscope Packages. Orders must be placed before Oct. 31, 2001 to receive discount. Orders placed on-line will be given a 5% discount by the shopping cart. When we receive the orders in-house, we will take another 10% off before processing the order. Download Sale Price List to check for packages that are on sale. Go to Scienscope Packages Page |
| Scienscope is proud to introduce its newest in Stereo
Zoom Microscopes. The SSZ series Stereo Zoom Microscope offers
excellent optics and long lasting durability, for a very reasonable
price. With a magnification range from 2x - 225x, and super long
working distances (up to 12"), the SSZ series microscope is an excellent
solution for various applications in need of magnification.
Parfocal ability allows you to scan at lower magnifications and then ZOOM in to take a closer look at
your sample; all without loosing
focus. See the SSZ Series Specifications and Breakdown
|
To Order Call
1-800-394-1984 and tell us
you seen it in the newsletter to receive the Newsletter Special Price.
|
Tips for Tips on the Xytronic's 988, 968 |
Common Causes for Tip Failures:
1. Tip temperatures
higher that 410°C (770°F).
2. The tip working surfaces are not tinned while
the iron idling.
3. Lack of flux in soldering, wicking, repair, and touch-up
operations.
4. Wiping the tip on a high sulfur content, dirty or dry
sponge.
5. Contact with organic substances such as plastic, resin, silicone,
grease
and other chemicals.
6. Impurities in the
solder and/or low tin content.
Care of Tips:
Caution: The
soldering, desoldering irons can reach very high temperatures.
Be sure
to turn the unit off prior to carrying out any maintenance
or trouble
shooting steps listed below!
Important: Remove the tip and clean after
each moderate to heavy use or daily
for light usage. Remove any loose
build up in the tip retaining assembly
to prevent tip
freezing.
Both solder, desolder tips supplied are iron clad copper and if
used properly should
maintain optimum life.
1. Always tin the
tip before returning it to the holder, turning off the station,
or
storing it for long periods of time. Wipe the tip on a wet sponge or
our
tip cleaner 460 prior to use.
2. Keeping the iron set at high
temperatures (more than 400°C or 750°F) will
shorten tip life.
3. Do
not use excessive pressure on the tip or rub the joint with the tip
while
soldering and/or desoldering, it does not improve the heat
transfer and may
damage the tip.
4. Never clean the tip with a file
or abrasive materials.
5. Do not use fluxes, which contain chloride or acid.
Use only rosin or resin activated
fluxes.
6. If an oxide film forms,
it can be removed by careful buffing with a 600-800 grit
emery cloth,
isopropyl alcohol or equivalent and then wrapping rosin core
solder
around the newly exposed surface. Coat the tinned areas with
rosin-core solder after
the resin-core has melted.
New
Tips:
Applying the following steps give the tip optimum life.
1.
Set both temperatures to min. Then turn the main power switch to the "ON"
position.
2. Set soldering tip temperature to 250°C (500°F approx.) and
desoldering tip
temperature to min. Coat the timed surfaces with
rosin-core solder after reaching 250°C.
3. Set to the desired temperature
about 3 minutes after being warmed that the station
will be ready for
use once it reaches preset temperature.
Important: Remove and clean
the tip daily. If a new tip is installed, remove any loose
build up in
the tip and barrel assembly, otherwise the tip may fuse to the heating
element
or retaining barrel.
|
60 day 100% Total Satisfaction Guarantee |
HEI now offers you a 60 day 100% Total Satisfaction
Guarantee
Other exciting Products can be seen at http://www.howardelectronics.com/
You will be receiving more cost saving
newsletters from us in the future. If you feel like this
newsletter
will not benefit you, but would like to forward it to someone else in your
organization
go to www.howardelectronics.com/emailform.html
or if you would prefer to be completely
removed from our customer
savings list click remove@howardelectronics.com
to be taken off
our mailing list.
Before you commit to this,
remember that we are trying to help you with new tools and information
to
create a better and easier working environment. Our goal is to
become Your Soldering and Desoldering
Specialists.
974 SE Pioneer Rd.
Kechi, KS
67067
(Outside of Wichita, KS)
1-800-394-1984 Toll Free
(USA and Canada)
01-316-321-2800 International
Phone
316-321-2803 Fax
info@howardelectronics.com
Our Shop Safe
Guarantee
