Howard Electronic Instruments Soldering and Desoldering
|
Hot Products
Xytronic Soldering & Desoldering Station
Only $299.00
Buy of the Year
HG3002LCDKIT
Heat Gun Kit
Sale $149.00
 |
|
|
DEN-ON SD3000II SMT Rework
Station |
| This rework system is designed to remove most SMT components
like QFPs, SOPs, PLCCs SOJs, PGAs, BGAs, Connectors and other chips.
It does not require any special nozzles or additional accessories.
Built in timer to prevent overheating of board and component. The
hot air nozzle has an adjustable motion range of up to 50mm per
axis. |
|
|
Control Panel |
Rotating Nozzle |
Vacuum Pickup Tool |
Hot Air Nozzle |
 |
 |
 |
 |
|
|
SPECIFICAIONS |
|
Heating Method |
HOT AIR NOZZLE
-4mm, 350 Watts |
|
Airflow Rate |
1.5L - 12L/min
in 8 Steps |
|
Air Pump and Vacuum |
Internal, Does
not Require Shop Air |
|
Nozzle Motion Range Maximum |
X and Y
Motion=50mm, Z=25mm |
|
Temperature Control |
Analog with
Digital Readout for 260 to 600
Degrees C |
|
Timer Control |
Analog with
Digital Readout for 5 - 500 seconds |
|
Max.PCB Size |
Throat
Depth=420mm, Width=Any Size |
|
Power Consumption |
100,120, or
230VAC, 350 Watts |
|
Dimensions |
300mmW x
310mmHx 450mm D |
|
Weight |
9kg |
|
|
|
OPERATION FOR REWORK OF MICRO COMPONENTS |
- Set the Knob of X & Y in 1
(reading) and set the Knob of BLOW
in 1-2 With the Power "ON", the
NOZZLE is inclined forwards. Observe
the target component with the
optional MONITOR& CAMERA and remove
or place the component.
- The SMT PIN is available to
assist in the removal and placement
of the micro-components.
|
|
|
|
ACCESSORIES |
- Vacuum Pick
(Tweezer)
- 3 Suction
Pads (Cups) for
Vacuum Pick
(Tweezer)
- 5 Filters
for Vacuum Pick
(Tweezer)
- Base Plate
with 430mm x
300mm
- 2 for PCB
Holder Small
(P/#H-1)
2 for PCB Holder
Large (P/#H-2)
- Base Plate
Stand (P/#S-1)
- PCB Support
Pin (P/#H-3)
- Metal Frame
(P/#20-10-10)
|
|
|
|
OPTIONS |
- Monitor &
Camera to Assist
in rework of
Micro Components
- Auxiliary
Holder for Small
Boards
- SMT PIN for
Rework of Micro
Components
|
|
|
FAST EFFICIENT PRE-HEATER : PH-3100A |
PH-3100A $1800.00
|
OUTLINE
This
pre-heater
uses 2 200W
IR heaters
and closed -
loop control
to enable
fast and
safety
manual
soldering.
It is
designed for
multilayered
PCB under
Lead-free
solder with
large heat
sinks. |
FEATURES
-
Total
400W IR
of
Heating
Power -
Ensures
the heat
is
saturates
evenly
and
smoothly
over
multilayered
PCB
allowing
for fast
manual
soldering.
- PCB
holders
and
Bottom-side
Supports
Included
- Allows
for set
up and
use set
for
preheating
without
the need
for
additional
purchases
of
accessories.
- Wide
Area
Heating
Design -
The
large
area
heating
design
helps
prevent
the
board
from
warping
due to
uneven
heating.
- This
pre-heater
is also
designed
for use
with the
Den-on
SD-3000
II Spot
Convection
SMT
Rework
Machine.
|
|
|
|
|
Howard Electronic Instruments, Inc. Address and Information
Copyright © 1996 - 2012 Howard Electronic Instruments, Inc. All rights reserved.
Current date CST:
02/11/2012
|
|
|
|
DEN-ON Products
Print this page
Articles of Interest
SC-7000Z
Testimonials
SC-7000ZTP
SMD KIT
ST-800 Stand
SC-7000Z TIPS
Solder Stations
SS-8400
SS8200
SD-3000II
Soldering Tips
MANUALS
PARTS
CATALOG
|
